Plastering advice for Lowestoft homes
Damp, salt and plaster: why walls fail near the sea
You have a wall that will not stay painted. It blisters, you scrape and repaint, and by spring it has blistered again in the same place.
The paint is not the problem and nor, really, is the plaster. The problem is water, and the salt it carries. In a town on the North Sea, that is worth ten minutes of your time.
What salt does to a wall
Bricks and mortar are full of tiny holes. When a wall gets wet, water moves through those holes and dissolves salts on the way. The water heads for the warm, dry side of the wall, which is your room. There it dries off into the air and leaves the salt behind.
As the salt dries it forms crystals, in and behind the plaster, and they prise it apart a grain at a time. First the paint lifts. Then a white fluffy bloom appears. Then the plaster turns to powder.
Some salts also pull water out of the air. A wall loaded with them can feel damp on a muggy day even when no new water is getting in. This is why plaster that has been through a flood can go on misbehaving after the house has dried.
Where the water comes from
Rain driven through the wall
The usual culprit on an exposed coast. Cracked render, worn pointing, a leaking gutter or a failed seal round a window lets rain in. The patch indoors is often high on the wall, or below a window, and gets worse after storms.
Damp rising from the ground
Low on the wall, up to about a metre. Often the cause is simple: soil or paving outside built up above the damp-proof course, or a blocked air brick.
Condensation
Black mould in corners, behind wardrobes and round windows. This is moisture from inside the house settling on cold surfaces. It spoils paint more than plaster, and it is cured by heat and fresh air, not by a plasterer.
Leaks
A brown-edged stain on a ceiling or beside a pipe run. Once the leak is fixed and the area is dry, the repair is simple.
Flood water
Parts of Lowestoft flooded in 1953 and in the storm surge of December 2013. Sea water leaves a heavy load of salt in a wall.
Why new plaster by itself will not fix it
A fresh skim looks perfect for a few months. The water is still arriving and so is the salt, so the new plaster goes the way of the old. People sometimes pay for the same wall three times before anyone asks how the water is getting in.
Stop the water first. That may mean a roofer, a builder or new render before it means a plasterer.
What a plasterer does once the wall is dry
- Takes off all the plaster that has been damp, and a margin beyond it, because salts spread further than the stain.
- Lets the bare wall dry, which takes weeks and sometimes months.
- Brushes off any salt that comes to the surface as it dries.
- Replasters with something suited to the wall. On old solid walls that often means lime, which lets the wall go on drying. Where salts are heavy, a renovating plaster made to cope with them may be used.
- Keeps the new plaster clear of a solid floor at the bottom, so damp cannot bridge across.
A UK plastering guide says damp work can add around £3,250 for treating rising damp and around £900 for damp that comes in through a wall, depending on the size of the area. Those are UK guide figures for the damp work itself, before any plastering.
A five-minute check you can do today
- Look at the outside of the damp wall for cracks, missing pointing and green streaks
- Watch the gutters and downpipes on that wall when it rains
- See if the ground outside is higher than the floor inside
- Tape a square of kitchen foil over the patch for a few days. Drops on the room side point to condensation. A dark, wet wall behind the foil points to damp coming through
- Note if the patch is worse after rain or after a cold night
Write down what you see and add it to the form. A plasterer who knows the likely cause before they arrive can tell you straight if they are the right trade to begin with. Inside work is covered on our pages for plaster repairs and replastering.
Common questions
Can you plaster over a damp wall?
Not with any hope of it lasting. Ordinary plaster on a damp wall stays wet, will not hold paint and comes loose. The source of the damp has to be stopped and the wall allowed to dry first.
What is the white fluffy stuff on my wall?
It is salt, left behind as water dries out of the wall. Builders call it efflorescence. Brush it off dry. Do not wash it, as water just carries it back in. If it returns, the wall is still getting wet.
Find the cause of the damp first
Damp does not pause while you decide. Each wet winter moves more salt into the wall and loosens more plaster, and timber touching damp brick will begin to rot. The earlier the source is found, the smaller the patch that has to come off.
Describe the patch and say where in Lowestoft the house is. No bill follows the phone call.